PowerMatch – Matches machine power output to what the conditions require. When hilly terrain and challenging mowing require more power than the 24.8 hp engine can provide, the Reelmaster 5010-H sheds the cutting unit load from the engine to the battery pack. If even more power is required, the battery pack boosts the engine power, giving the machine the equivalent of over 40 horsepower.

The battery pack is made up of four, 12-volt, Absorbed Glass Mat (AGM) batteries that are maintenance-free and sealed. The batteries are very similar to the ones used in the automobile industry for start-stop hybrids. These batteries are designed for a very long life when they are shallowly discharged and repeatedly recharged with a system like our PowerMatch. Depending on usage, the life expectancy will vary, but in an average golf course duty cycle, the battery pack can be expected to last years of operation.

If the blades get bogged down, Smart Power adjusts their speed for proper cut. Individual deck motors control blade speed for the best after-cut appearance.

Easily keep a consistent speed and reduce fatigue while mowing large areas.

Removing the hydraulic cutting mowers and replacing them with electric motors on the Reelmaster 5010-H resulted in over 100 fewer leak points than a conventional 254 cm fairway mower. The remaining vehicle and cutting unit lift system hydraulic lines are predominately hard lines or hoses with limited movement, and are not subject to the same fatigue or service intervals as the cutting unit hoses and motors. As the electric reel circuit requires no scheduled maintenance, it further reduces the cost of ownership.

Consistent reel speed – the electric reel motors allow for precise setting of the clip and consistent power across all five cutting units for a superior cut. The cutting units also feature low-drag seals and low-friction bearing which improve wear and reduce the required horsepower to run the decks.

Precision machined cutting units maintain levelness and hold adjustments. Dual Precision Adjustment (DPA) allows quick bedknife to reel adjustment. New style cutting units, which feature low-friction seals and bearings on the reels, further reduce power demands and increase fuel efficiency. Toro’s EdgeSeries reels enable longer edge retention thus reducing grinding and backlaping.

The InfoCenter display makes maintenance and diagnostics quicker and easier for technicians. The onboard LCD display provides system information alerts, service reminders, diagnostics, fault codes and vehicle and cutting unit adjustments that are easy to see and understand. Precisely control reel speed and clip rate, monitor reel performance and view reel diagnostics with the onboard InfoCenter.

Easily customise clip for different heights of cut and adjust other operational settings to gain complete machine control. Common operation information displayed includes: reel speed, hours of function, system voltage for reels, diagnostic descriptions, and much more.

With more than enough horsepower and highly efficient components, the TriFlex Hybrid models operate efficiently in energy savings mode. While in this mode, engine RPM’s are reduced and the all-electric reel drive maintains a constant reel speed. This results in reduced fuel consumption and noise while maintaining quality of cut, performance, and productivity.

The electrical connectors and components are completely protected permitting machine wash down without worry.

The suspension system maintains full floatation range to prevent gouging or scalping when going over undulations.

Superior contour following capability utilizes an integrated “Flex” linkage system to allow cutting units to pivot around the center of the front roller to master undulations and prevent side-to-side scrubbing of the putting surface.

Precision manufactured cutting units with minimal adjustments and the proven ability to maintain adjustment for longer periods of time provide superior cutting performance.

The suspension system is designed to provide a slight lift to the inside of the cutting units during turns to deliver a consistently level cut and to reduce “triplex ring” for improved playability and turf health.

Easy access to the center cutting unit facilitates routine maintenance and repairs, simplifies adjustments, and eliminates the need to put the traction unit on a lift for cutting unit service saving you time, money, and frustration.

A single operator can go from cutting Greens at 3.2 mm ( 0.12″) to cutting a Fairway at 19 mm in just a few minutes. The tool-free, quick-change cutting units make it as easy as 1-2-3.

Redesigned clipping capture system maintains a consistent gap between the basket and reel to retain nearly all grass clippings for a cleaner and healthier cut. In addition, a discharge shield forces clippings inside of basket and minimises “blow-by”.

Tyres have been redesigned to deliver uniform loading across the entire cross-section (load footprint area) to eliminate side wall loading that can create visible tire tracks.

The Triangle Wheel Stand places the rear wheel track within the radius of the front wheel, which prevents accidentally dropping the rear wheel into a nearby sand bunker while making the turn for the next mowing path.

In addition to eliminating hydraulic leaks, each reel motor has a nominal 1.5 horsepower (1.1 kW) that can increase up to 3.0 hp (2.2 kW) during peak load periods. This translates into the power you need when you need it for unparalleled performance in your most challenging cutting or verticutting applications.

Eliminates clip marks at startup of mowing path.

The dependable Turf Guardian leak detection system provides immediate audio and visual indication of possible hydraulic fluid leaks.

Powered by a 49 hp (36.5 kW) Kubota® diesel engine, this Reelmaster model provides plenty of power to climb hills, even while operating groomers and rear roller brushes.

Precision machined cutting units maintain levelness and hold adjustments. DPA allows quick bedknife to reel adjustment. The Toro EdgeSeries represents the next generation of cutting quality and durability, with enhanced cutting edge retention. In addition to new reel material, the EdgeSeries incorporates a new reel geometry design, and changes in the manufacturing process that result in a more accurate cut. The innovative design and manufacturing changes to the reel and bedknife provide a better after-cut appearance and a reduction in required maintenance. The EdgeSeries provides multiple benefits that require less labour to maintain the reel and bedknife, and leave your grounds looking their absolute best.

By adding two 81 cm rear cutting units the overlap area can be increased to almost 15 cm thus eliminating the possibility of uncut grass in tight turns or on hillsides.

With this feature you get helpful maintenance reminders and instant notification of potential problems. During normal operation, the InfoCenter displays clear and simple operating information at a glance, while constantly monitoring the internal health of the machine. Audible and visual alarms notify the operator of a potential problem. In the field or at the shop, technicians can quickly identify the source of the issue. Allows operator to adjust sensitivity of electronically controlled foot pedal when moving. This allows the supervisor to set a maximum mowing speed for greater control of operator usage and quality.

Engineered with our exclusive SmartCool technology, so when things heat up under the hood, the system briefly reverses the cooling fan to blast chaff and debris from the air intake screens. The result, is non-stop improved productivity.

All of the indicators and controls to operate the unit are conveniently located on the right armrest. Control console pivots back for right hand entry and exit. Tilt steering, deluxe suspension seat, improved visibility and lower operating noise enhance the operator experience and help to reduce fatigue

Improved access to routine service points and service components, along with a robust machine design, results in less frequent maintenance intervals and less time is required to perform maintenance tasks.

Exquisite after-cut appearance for your fairways and roughs. Significantly reduce the time needed to scalp in preparation for overseeding.